Fully Formed 928 Spare Tire Cover - - Revisited
#31
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
I have bumped this thread in my other name, but the interest in these Spare Tire Covers seem to just go on and on. I have Just shipped one and have another fully finished and two more nearly finished and one more in the forming dies. If you have some interest in any one or more of these let me know.
__________________
ReDesign by FEATHER
by Jerry Feather
Producer for 928 of:
-Hatch Latch Receiver Liner--All Versions
-Replacement Heavy Duty Spare Tire Cover
-Flush Center Console Conversion
-Cowl Cover, Cowl Seal, & Shell Stickers--All versions
(RHD included)
-Aluminum Gas Cap Ratcheting Pawl
ReDesign by FEATHER
by Jerry Feather
Producer for 928 of:
-Hatch Latch Receiver Liner--All Versions
-Replacement Heavy Duty Spare Tire Cover
-Flush Center Console Conversion
-Cowl Cover, Cowl Seal, & Shell Stickers--All versions
(RHD included)
-Aluminum Gas Cap Ratcheting Pawl
Last edited by ReDesign by FEATHER; 05-03-2023 at 05:20 PM.
#33
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
#35
Rennlist Member
#38
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
I got your money, Aaron. I need your address. I'll ship it either later today or in the morning. Send the address to my email: jfeather@bresnan.net. Thanks.
P.S. Aaron's is shipped.
P.S. Aaron's is shipped.
Last edited by ReDesign by FEATHER; 05-05-2023 at 07:22 PM.
The following users liked this post:
Slavic (05-05-2023)
#39
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
I have had a nice run on these Spare Tire Covers this week and last and now find that I am out of material blanks. I just went to the Plastic store and bought another sheet and had it cut to blank sizes. I find that the price is way up, but I also ordered two more sheets and he thinks that the price might be a little less. Let's hope so. I hate to have to raise the price again.
I have one finished Cover, and Hans has spoken for that. I also have one formed in the forming dies, waiting for finish, and that was the end of the material I had on hand. I now have 7 new blanks to work with and will drill them up for placement in the dies this weekend.
Thanks to everyone who has stepped up for one of these. I'll try to keep up keeping up with them.
I have one finished Cover, and Hans has spoken for that. I also have one formed in the forming dies, waiting for finish, and that was the end of the material I had on hand. I now have 7 new blanks to work with and will drill them up for placement in the dies this weekend.
Thanks to everyone who has stepped up for one of these. I'll try to keep up keeping up with them.
#40
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
I continue to have the fully formed Spare Tite Covers available. I have had recent inquiry from one of you buyers about why I am charging so much for these when they can be had on Poliquin for pennies, in comparison, with free shipping.
Peliquin's are flat, and mine are fully formed as with the Factory ones . Given the price of the material and my increasing time involved, I am going to raise the price of mine to$150 plus S&H.
Peliquin's are flat, and mine are fully formed as with the Factory ones . Given the price of the material and my increasing time involved, I am going to raise the price of mine to$150 plus S&H.
The following users liked this post:
Adamant1971 (08-26-2023)
#45