Rennlist - Porsche Discussion Forums

Notices
 
Page 1 of 20
1
2
3
4
5
6
11
Last »
Search: Posts Made By: Mrmerlin
Showing results 1 to 25 of 500
Search took 0.35 seconds.
Forum: 928 Forum
Today, 10:32 AM
Replies: 2
Views: 108
Posted By Mrmerlin

Nice looking S4 , have you inspected the coil...

Nice looking S4 ,
have you inspected the coil wires for corrosion on their ends,
and made sure they dont touch anything along their run.

When was the intake refresh completed?
Has the LH and...
Forum: 928 Forum
Today, 10:26 AM
Replies: 140
Views: 6,055
Posted By Mrmerlin

whats a transmission coupler? If your...

whats a transmission coupler?
If your referring to the input collar on the trans axle please be very careful here.
NOTE be very careful when unbolting the TT from the trans axle,
any side loading...
Forum: 928 Forum
Yesterday, 02:49 PM
Replies: 16
Views: 315
Posted By Mrmerlin

the LH could have just failed . Please answer...

the LH could have just failed .
Please answer this question,
when you turn the key to run do you hear the injectors clicking ?
What is clicking
Forum: 928 Forum
Yesterday, 11:41 AM
Replies: 16
Views: 315
Posted By Mrmerlin

whats the condition of the temp 2 sensor and it...

whats the condition of the temp 2 sensor and it connector?
Forum: 928 Forum
Yesterday, 10:36 AM
Replies: 16
Views: 315
Posted By Mrmerlin

OK lets get more info here from your clues, ...

OK lets get more info here from your clues,
first if you turn the key to run, are you saying that you hear a clicking from the engine?
Like the injectors are clicking without the engine running?...
Forum: 928 Forum
Yesterday, 09:37 AM
Replies: 28
Views: 825
Posted By Mrmerlin

NOTE on installing any NEW or recently...

NOTE on installing any NEW or recently refurbished injectors.
they should be checked for operation prior to installing them.
to do this use a 9 volt battery with a 2 pin AMP connector soldered to...
Forum: 928 Forum
04-23-2024, 10:03 PM
Replies: 28
Views: 825
Posted By Mrmerlin

smell the vacuum lines for fuel , with it warm...

smell the vacuum lines for fuel ,
with it warm hold your foot to the floor and crank it.
you could also have a leaking injector.
why not put the old injectors back in after you get them cleaned
Forum: 928 Forum
04-23-2024, 05:34 PM
Replies: 21
Views: 996
Posted By Mrmerlin

Mike I would try some of this on your seats, it...

Mike I would try some of this on your seats, it may help with the aging process

...
Forum: 928 Forum
04-23-2024, 01:44 PM
Replies: 31
Views: 1,552
Posted By Mrmerlin

Umm I dont think the Constantine clamp works on a...

Umm I dont think the Constantine clamp works on a 5 speed.

More than likely the clutch is out of balance,
the clamps are balanced at the factory.
I would have the I clutch package balanced...
Forum: 928 Forum
04-23-2024, 01:27 PM
Replies: 28
Views: 825
Posted By Mrmerlin

Here is some more backround info for the...

Here is some more backround info for the mechanics.
Its pertinent to this particular series of 928 models with the big plenum intakes.

IMHO The IR gun is the safest way to find a non firing...
Forum: 928 Forum
04-23-2024, 09:35 AM
Replies: 8
Views: 274
Posted By Mrmerlin

Chris< Based on your response you do not...

Chris< Based on your response you do not understand what your being advised.

That mangled part # 21 in the drawing, must be removed from the bottom of the cross member support, first.

Then...
Forum: 928 Forum
04-22-2024, 10:32 PM
Replies: 28
Views: 825
Posted By Mrmerlin

I never said that they cant be wired any way. ...

I never said that they cant be wired any way.
they can,
it doesnt matter
a 9 volt battery soldered to the wires of a 2 pin AMP connector makes it easy to test all the injectors.
So you installed...
Forum: 928 Forum
04-22-2024, 10:29 PM
Replies: 10
Views: 528
Posted By Mrmerlin

he can also go into through center door panel, ...

he can also go into through center door panel,
remove one screw ,
cut the vapor barrier ,put the window up.
Forum: 928 Forum
04-22-2024, 07:44 PM
Replies: 28
Views: 825
Posted By Mrmerlin

well thats great, Now all you need is a 9 volt...

well thats great,
Now all you need is a 9 volt battery soldered to a 2 pin AMP connector to test each injector for a click.
If you find one not clicking then you should remove it,
spray PB blaster...
Forum: 928 Forum
04-22-2024, 11:56 AM
Replies: 2
Views: 138
Posted By Mrmerlin

under each of the fenders are 2 lamp stops they...

under each of the fenders are 2 lamp stops they used to have rubber nubbers on them,
these are adjustable.
That HL motor should be fastened securely.
Forum: 928 Forum
04-22-2024, 11:52 AM
Replies: 3
Views: 208
Posted By Mrmerlin

yes its one of the easiest bolts to attach a P...

yes its one of the easiest bolts to attach a P clamp and ground wire to the lifting bracket...
LOL
Thats a joke friends. I saw someone use a stud for this.
Forum: 928 Forum
04-22-2024, 09:29 AM
Replies: 2
Views: 212
Posted By Mrmerlin

Put the strut in put the three bolts on the top...

Put the strut in put the three bolts on the top to hold it in place

put the upper control arm in.

put the lower control arm in .install the lower shock bolt and sway link
get your floor Jack ,...
Forum: 928 Forum
04-20-2024, 10:15 PM
Replies: 13
Views: 428
Posted By Mrmerlin

on the new light sockets you need to trim off one...

on the new light sockets you need to trim off one of the small nubs,
IIRC its opposite the wide nub but check,
then the socket will pass into the housing then turn it and it should lock.
NOTE...
Forum: 928 Forum
04-20-2024, 10:05 PM
Replies: 28
Views: 825
Posted By Mrmerlin

please run a test on your TPS connector at the...

please run a test on your TPS connector at the computer its a slight possibility that the wires could be reversed.
you want to verify that the TPS signal works for idle and then for WOT.

verify...
Forum: 928 Forum
04-20-2024, 08:37 PM
Replies: 3
Views: 355
Posted By Mrmerlin

I would look for another engine, whatever your...

I would look for another engine,
whatever your next engine is you will still be pulling the heads to do HGs,
unless you find a good engine thats already had this performed.

NOTE the machine work...
Forum: 928 Forum
04-20-2024, 08:29 PM
Replies: 31
Views: 4,442
Posted By Mrmerlin

Wow your certainly knee deep in the hoopla. is...

Wow your certainly knee deep in the hoopla.
is this an auto?

If so I would suggest that you do a flex plate inspection and check the crank end play. report what you find ,
also make sure to...
Forum: 928 Forum
04-20-2024, 08:21 PM
Replies: 28
Views: 825
Posted By Mrmerlin

did you replace the CPS with a new Bosch part? ...

did you replace the CPS with a new Bosch part?
or just the connector?
Could you have swapped the ICV and CPS connectors?
this is easy to check go from the computer connector

Did you replace...
Forum: 928 Forum
04-20-2024, 08:13 PM
Replies: 1
Views: 239
Posted By Mrmerlin

looks like M10x 55 also should have a thicker...

looks like M10x 55 also should have a thicker washer on it
Forum: 928 Forum
04-18-2024, 06:08 PM
Replies: 123
Views: 11,869
Posted By Mrmerlin

BC I use a fuel injection line clamps no swages....

BC I use a fuel injection line clamps no swages. for the fuel return to the sender.
Also they make 2 different transfer hoses,
( this vents the body of the tank to filler neck and goes through the...
Forum: 928 Forum
04-18-2024, 04:35 PM
Replies: 4
Views: 223
Posted By Mrmerlin

Use any color you like, I prefer gloss white,...

Use any color you like,
I prefer gloss white, it makes finding leaks easier.
and use hi heat engine paint 500 F
I would not flush anything into the TC,
just wipe it off .
NOTE put some vaseline...
Showing results 1 to 25 of 500
 
Page 1 of 20
1
2
3
4
5
6
11
Last »


 
Forum Jump


All times are GMT -3. The time now is 01:12 PM.