Rennlist - Porsche Discussion Forums

Notices
 
Page 1 of 20
1
2
3
4
5
6
11
Last »
Search: Posts Made By: fast951
Showing results 1 to 25 of 489
Search took 0.56 seconds.
Forum: 944 Turbo and Turbo-S Forum
07-05-2023, 01:39 PM
Replies: 11
Views: 645
Posted By fast951

4 deg at Idle is about right. If you suspect...

4 deg at Idle is about right.

If you suspect the problem is timing related, record ignition timing at 1000, 1500, 2000, 2500 and 3000.
Compare your results with someone running a similar kit.
Forum: 944 Turbo and Turbo-S Forum
07-02-2023, 01:39 PM
Replies: 11
Views: 645
Posted By fast951

Is the no power at 3000rpm happens every time...

Is the no power at 3000rpm happens every time when you hit 3000rpm? Is it "RPM" related, or is there something else taking place around 3000rpm (like start building boost)?

The 3000rpm issue could...
Forum: 944 Turbo and Turbo-S Forum
07-02-2023, 01:33 PM
Replies: 11
Views: 645
Posted By fast951

The flywheel tooth count is a "static" value on...

The flywheel tooth count is a "static" value on the chip!

Where are you reading the tooth count? How is it being counted?

If your logger is counting "actual" teeth directly off the flywheel,...
Forum: 944 Turbo and Turbo-S Forum
06-26-2023, 11:14 PM
Replies: 19
Views: 1,772
Posted By fast951

NO! The chip must be configured/programmed to...

NO! The chip must be configured/programmed to work with the injectors used (based on size and characteristics). Fuel Pressure must be known as well during the chip configuration.

It is possible...
Forum: 924/931/944/951/968 Forum
06-10-2023, 11:27 AM
Replies: 6
Views: 786
Posted By fast951

The Vitesse MoMonitor reports the status of the...

The Vitesse MoMonitor reports the status of the TPS (and other sensors) as the DME processes the sensor(s).
THe TPS should go from IDLE to PT to WOT. If you are going from Idle to WOT, then...
Forum: 944 Turbo and Turbo-S Forum
02-27-2023, 08:11 PM
Replies: 19
Views: 2,380
Posted By fast951

The Charley Aarms I have are late offset. I have...

The Charley Aarms I have are late offset. I have the std as well as the long pins. A few people expressed interest in the Aarms/spindles/hubs. I will probably wait till the track car sells.

The...
Forum: 944 Turbo and Turbo-S Forum
02-22-2023, 03:55 PM
Replies: 15
Views: 2,257
Posted By fast951

Thank you for the feedback and ideas. I know I...

Thank you for the feedback and ideas. I know I will not get anything close to what I have in it. I haven't used it in a while, and I doubt I will in the near future.

I love the looks of the 914/6....
Forum: 944 Turbo and Turbo-S Forum
02-22-2023, 03:44 PM
Replies: 19
Views: 2,380
Posted By fast951

Thank you for your interest. At this point,...

Thank you for your interest.

At this point, I'm trying to determine the value of the parts. Then I'll decide what to sell.
Forum: 944 Turbo and Turbo-S Forum
02-21-2023, 05:15 PM
Replies: 15
Views: 2,257
Posted By fast951

Where is the best place to market a track only 951?

I'm aware of the increased value of the 951. But how about track only 951s?

How do you establish a value of a heavily modified 951 track car (cage, engine, suspensions, lexan, wide body... Non...
Forum: 944 Turbo and Turbo-S Forum
02-21-2023, 05:09 PM
Replies: 21
Views: 2,551
Posted By fast951

With a K26/6 or K26/8 (even K27/6) the stock...

With a K26/6 or K26/8 (even K27/6) the stock exhaust (if in good condition) is fine. Going to a larger 3" exhaust will not yield much.
Ask people selling the 3" exhaust to show you before/after...
Forum: 944 Turbo and Turbo-S Forum
02-21-2023, 04:54 PM
Replies: 19
Views: 2,380
Posted By fast951

Price Check - 16V heads, Charlie Arms, LSD transaxles?

Over the years, I collected all sort of parts. Some, I doubt I will use any time soon.
I'm contemplating selling some of the parts, but I have no idea what some items are exchanging hands for...
Forum: 944 Turbo and Turbo-S Forum
11-05-2022, 05:02 PM
Replies: 20
Views: 5,498
Posted By fast951

Say hi to Ivan for me. I'll be glad to...

Say hi to Ivan for me.

I'll be glad to assist you. Drop me an email with your list of mods and your goals. Will go over the options that fit your needs.
Forum: 944 Turbo and Turbo-S Forum
08-19-2022, 12:32 PM
Replies: 19
Views: 1,772
Posted By fast951

When/if you switch back to the AFM you must use...

When/if you switch back to the AFM you must use an AFM chip tuned for the K27.

On a stock car, running stock boost, going to a MAF you will notice better response but not necessarily a big peak HP...
Forum: 944 Turbo and Turbo-S Forum
06-18-2022, 03:09 AM
Replies: 14
Views: 595
Posted By fast951

Based on the information I was given, this...

Based on the information I was given, this product is about 18-19 years old. It was discontinued 16+ years ago! Documentations were lost due to a computer crash years ago (not a fire).
Due to age...
Forum: 944 Turbo and Turbo-S Forum
05-19-2022, 06:04 AM
Replies: 17
Views: 1,586
Posted By fast951

Stock 951 injectors with a 3bar fuel pressure...

Stock 951 injectors with a 3bar fuel pressure support much more than the 186whp you are reporting.

Something else is going on. Fuel pump running out of flow? Restriction in lines between pump and...
Forum: 944 Turbo and Turbo-S Forum
04-21-2022, 11:41 PM
Replies: 24
Views: 1,292
Posted By fast951

Wow, this setup is still functioning. It's 19-20...

Wow, this setup is still functioning. It's 19-20 years old!

A very early setup! You must use all of the components together for it to work properly: MAF, injectors, FPR, and PiggyBack.
Change...
Forum: 944 Turbo and Turbo-S Forum
04-19-2022, 04:13 PM
Replies: 24
Views: 1,292
Posted By fast951

Notny41, I know you are trying to help the OP,...

Notny41, I know you are trying to help the OP, and it's appreciated! However, this is the perfect example of a hardware, software and instructions mismatch.
Once I figured what "you" have, I was...
Forum: 944 Turbo and Turbo-S Forum
04-19-2022, 04:05 PM
Replies: 24
Views: 1,292
Posted By fast951

OP - based on the pictures you sent, you do not...

OP - based on the pictures you sent, you do not have a "Stage 2 kit". Some of your parts date back to 2003. You have a S2 turbo from 2006-2007, and you are the 4th owner if not the 5th.
The...
Forum: 944 Turbo and Turbo-S Forum
04-06-2022, 08:12 PM
Replies: 6
Views: 697
Posted By fast951

Since you are getting fuel and spark on 1...

Since you are getting fuel and spark on 1 cylinder you can rule out the followings:
- DME
​​​- DME relay
- Speed & Ref sensors
- Fuel pump.

Things to check:
- Determine which cylinder is...
Forum: 944 Turbo and Turbo-S Forum
03-18-2022, 06:56 PM
Replies: 49
Views: 2,420
Posted By fast951

You remove the DME relay so you do not get fuel...

You remove the DME relay so you do not get fuel or spark when doing a compression test. Do not turn the engine with the starter (for compression test) till you check the bore (look for scratches on...
Forum: 944 Turbo and Turbo-S Forum
03-18-2022, 06:44 PM
Replies: 48
Views: 4,669
Posted By fast951

If stock pistons and a 3L crank, then the rods...

If stock pistons and a 3L crank, then the rods must be shorter. But the rods spec is showing stock 951 rod length.. A few more details would help.

The price is good (perhaps underpriced). The...
Forum: 944 Turbo and Turbo-S Forum
03-18-2022, 05:28 PM
Replies: 47
Views: 6,808
Posted By fast951

Nevermind. I use metric CHRA.

Nevermind. I use metric CHRA.
Forum: 944 Turbo and Turbo-S Forum
03-18-2022, 05:15 PM
Replies: 48
Views: 4,669
Posted By fast951

What brand pistons on the 2.8L? What CR?

What brand pistons on the 2.8L? What CR?
Forum: 944 Turbo and Turbo-S Forum
03-18-2022, 05:07 PM
Replies: 47
Views: 6,808
Posted By fast951

The 3/8 - M16 thread may work. But it's not...

The 3/8 - M16 thread may work. But it's not ideal. We machine inhouse our own brass fittings M - F M16 x 1.5, I may have a few left. Drop me an email on Tuesday, I'll check for you.
Forum: 944 Turbo and Turbo-S Forum
03-18-2022, 05:02 PM
Replies: 49
Views: 2,420
Posted By fast951

Spark plug does not look good. The milkshake...

Spark plug does not look good. The milkshake color is concerning (usually coolant+oil mix).

Inspect your oil and coolant. If no sign of mixing, continue to next step.

- remove DME relay to...
Showing results 1 to 25 of 489
 
Page 1 of 20
1
2
3
4
5
6
11
Last »


 
Forum Jump


All times are GMT -3. The time now is 09:06 AM.