Rennlist - Porsche Discussion Forums

Notices
 
Page 1 of 2
1
2
Search: Posts Made By: joel roeder
Showing results 1 to 25 of 40
Search took 0.42 seconds.
Forum: 928 Forum
10-17-2002, 12:59 AM
Replies: 24
Views: 632
Posted By joel roeder

Post as a mechanic. i feel for you in this situation....

as a mechanic. i feel for you in this situation. i dont understand tech,s that dont stand behind their work. (at any price). if you offer your time as a deal does it mean the deal gets the time your...
Forum: 928 Forum
09-21-2002, 11:27 AM
Replies: 3
Views: 279
Posted By joel roeder

Post bleeding a clutch can be areal pain on some cars....

bleeding a clutch can be areal pain on some cars. you can sometimes do a gravity bleed, open the bleeder on the slave and keep the fluid full till it drips, close vale. then have sombody push the...
Forum: DIY - 928
09-21-2002, 11:27 AM
Replies: 3
Views: 6,832
Posted By joel roeder

Post bleeding a clutch can be areal pain on some cars....

bleeding a clutch can be areal pain on some cars. you can sometimes do a gravity bleed, open the bleeder on the slave and keep the fluid full till it drips, close vale. then have sombody push the...
Forum: 928 Forum
09-21-2002, 11:09 AM
Replies: 6
Views: 252
Posted By joel roeder

Post you could try a dye in the oil to verify leak....

you could try a dye in the oil to verify leak. next ck the crankcase ventilation. next would be to ck compression and cylinder leak down test,s.
maybe a heavier oil would would help. even if you...
Forum: 928 Forum
09-21-2002, 10:59 AM
Replies: 10
Views: 385
Posted By joel roeder

Post hi wally, think you could reword this to fit a...

hi wally, think you could reword this to fit a shop application, tail light warranty stuff. you pay for wrong guess,s. that kinda stuff. good post for this forum though. hope all is well
...
Forum: 928 Forum
07-31-2002, 12:28 AM
Replies: 23
Views: 864
Posted By joel roeder

Post hi. first off the sight glass means nothing with...

hi. first off the sight glass means nothing with 134. you now need to pull out the freon and recharge to 80% of r12 value. then post your presures. next, there is a motor on the left side of heater...
Forum: 928 Forum
07-28-2002, 01:43 AM
Replies: 9
Views: 508
Posted By joel roeder

Post i didnt notice a mention to the o-ring behind the...

i didnt notice a mention to the o-ring behind the thermostat. does this modle not have it? i have found the infored temp guns to be very acurate. good luck
Forum: 928 Forum
07-28-2002, 01:06 AM
Replies: 25
Views: 858
Posted By joel roeder

Post well now, mr struthers certainly has put a new...

well now, mr struthers certainly has put a new lite on ooo wool cleaning. i have used the wool trick for 20 some odd years both in the north and in the south and have never seen the likes of johns...
Forum: 928 Forum
07-26-2002, 11:53 PM
Replies: 6
Views: 329
Posted By joel roeder

Post perhaps at this speed the coolant overflow hose...

perhaps at this speed the coolant overflow hose is aimed in such a way as to catch the wind and act as a siphon. with a little vacuum applied at the highest coolant presure it wouldnt take much to...
Forum: 928 Forum
07-26-2002, 11:45 PM
Replies: 5
Views: 25,730
Posted By joel roeder

Post cold start valve function is the enitial shot of...

cold start valve function is the enitial shot of fuel to start cold engine. once you start the warm up regulator can take up the slack in so far as running a richer mixture during cold engine warm...
Forum: 928 Forum
07-26-2002, 11:08 PM
Replies: 25
Views: 858
Posted By joel roeder

Post best i have found so is wurth window cleaner....

best i have found so is wurth window cleaner. expensive but good, otherwise i try windex with 0000 steel wool.
Forum: 928 Forum
07-23-2002, 10:32 AM
Replies: 5
Views: 345
Posted By joel roeder

Post most deffinatly a bad ground, recheck your work...

most deffinatly a bad ground, recheck your work maybe. good luck
Forum: 928 Forum
07-23-2002, 10:28 AM
Replies: 7
Views: 591
Posted By joel roeder

Post hi wally. i think any expansion valve is...

hi wally.
i think any expansion valve is capable of freezer status. i agree that the freeze switch is at falt and am wondering if anyone in the list ever figured out the gm part number on this...
Forum: 928 Forum
07-23-2002, 12:39 AM
Replies: 7
Views: 319
Posted By joel roeder

Post i dont know how deep your ck,s have gone so far...

i dont know how deep your ck,s have gone so far but have you ck,d the tps at idle position. the cpu needs idle contact to want to run the idle air valve properly. also the throttle plate itself needs...
Forum: 928 Forum
07-23-2002, 12:28 AM
Replies: 7
Views: 591
Posted By joel roeder

Post dozman, the vehicle was charged at 80% of the r12...

dozman, the vehicle was charged at 80% of the r12 spec. sucked down and recharged to the 80%. just to make sure of no issues or mistakes. the presures at idle and the temp at idle are not even close...
Forum: 928 Forum
07-22-2002, 02:33 AM
Replies: 5
Views: 480
Posted By joel roeder

Post sorry not to get back sooner on this one, my...

sorry not to get back sooner on this one, my thanks to tony and don. you were spot on tony. and don that site you mentioned is really very informative.at the end of a long hot day you pull an oil pan...
Forum: 928 Forum
07-19-2002, 12:43 AM
Replies: 5
Views: 480
Posted By joel roeder

Post by the way this is an 86 euro 928 auto.

by the way this is an 86 euro 928 auto.
Forum: 928 Forum
07-19-2002, 12:19 AM
Replies: 5
Views: 480
Posted By joel roeder

Post thanks donald, but after reading the info at that...

thanks donald, but after reading the info at that site, all good info i might add, i realized that the wear on this block is at the rearward block surface number one and secondly there is no...
Forum: 928 Forum
07-18-2002, 09:35 PM
Replies: 5
Views: 480
Posted By joel roeder

Post crankshaft end play, wear?

hey guys, miss joann from maryland whom many of you met at the mountain event this last spring stopped in on her way to fla. and asked for some ac help and electrical help. when i drove her car in at...
Forum: 928 Forum
07-18-2002, 10:03 AM
Replies: 3
Views: 291
Posted By joel roeder

Post clear silcone is what i use on any non-stress...

clear silcone is what i use on any non-stress glue job it cleans easy and releases when you need it to. bonds plastic to plastic or plastic to metal real well luck.
set up time isnt all that great....
Forum: 928 Forum
07-18-2002, 09:58 AM
Replies: 1
Views: 295
Posted By joel roeder

Post adjustable sway bar links

one of my custumers installed the sway bar links front and rear and the said it drives worse. at what length have you folks found the best proformance on these adjustable links. (he is a very...
Forum: 928 Forum
07-18-2002, 09:43 AM
Replies: 4
Views: 329
Posted By joel roeder

Post the voltage regultor does somtimes need a little ...

the voltage regultor does somtimes need a little rev to wake up. it may also indicate a weak ground from alt. to block.
Forum: 928 Forum
07-14-2002, 02:07 PM
Replies: 6
Views: 403
Posted By joel roeder

Post good post thom, i did run into a tensioner that...

good post thom, i did run into a tensioner that didnt show much wear but wound up pulling an engine thinking somthing had fallin in the cylinder and was going to get it out. upon removal we found the...
Forum: 928 Forum
07-14-2002, 01:55 PM
Replies: 4
Views: 341
Posted By joel roeder

Post thom, if you have a set of manuals it tells you...

thom, if you have a set of manuals it tells you how to ck and adjust the temp motor mounted on the left side of the box, behind cluster is easiest approach. then remove glove box and set the two...
Forum: 928 Forum
07-14-2002, 11:58 AM
Replies: 4
Views: 276
Posted By joel roeder

Post a quick note on relays, hi wally good suggestion,...

a quick note on relays, hi wally good suggestion, anytime you have your fuse panel open its not a bad idea to take a screwdriver handle and tap all relays. if they falter you know thats the next new...
Showing results 1 to 25 of 40
 
Page 1 of 2
1
2


 
Forum Jump


All times are GMT -3. The time now is 05:52 AM.