pat056

I disconnected my battery just before Christmas and lost my water temp. digital readout. I did a quick (i.e. lazy) search trying to find the thread that descrices how to make the air temp readout on the dash console show the water temp. I left the instructions at work and have been off for 2 weeks. Anyone have that handy? Your supposed to push the recirc. and up arrow, or something like that.
Anyone remember what I'm talking about?

gota911

Pat - This may not be what you have been using, but here is a set of instructions. I don't know why I saved the instructions because they do not work on my '04. Hope this helps.

Porsche AC Diagnostics
(undocumented, unsupported feature)

The AC Climatronic unit is actually manufactured by Audi. There is some sort of serial data stream (not CAN) that allows the AC unit to display engine parameters. This works on 1997-2000 boxsters.

To switch from F to C:
Hold down the recirculating button then push both the temperature + - buttons.

To access diagnostics:
Hold down the Recirculating & Air up buttons for 5 seconds. The + - buttons go up and down through the list of "c" codes. The center vent button switches the left display between the "c" code and its actual value. Press the Auto button to exit.

I have yet to verify all these, this info was copied from wonderful people on PPBB!
Here is a list of what can be seen:


0c - ERL
1c - Oil Temp?
2c - Inside temp. Sensor mounted in the aspirator assembly at the side of the dash.
3c - Outside temp. Sensor located inside the air inlet of the A/C unit.
4c - Outside temp. Sensor located in front grill of the radiator. The data is fed to the Climatronic from the instrument cluster. When not moving, the instrument cluster OBC temp display retains it's last setting until moving. This is to prevent heat emanating from the radiator affecting the temperature sensor. The A/C unit uses the lower of the two outside air temp values in determining fresh-air temp.
5c - Outside temp. (matches OBC outside temp display)
6c - Coolant temp.
7c - Footwell discharge temp.
8c - Sun sensor (dash top)
9c - Sun sensor.
10c - Passenger compartment fan speed.
11c - Passenger compartment fan voltage.
12c - Temperature mix Flap command 1=COLD, 100=HOT
13c - Temperature mix Flap position
14c - Central Flap command
15c - Central Flap position
16c - Footwell/Defrost Flap command
17c - Footwell/Defrost Flap position
18c - Recirculation Valve command 1=OFF, 100=RECIRC
19c - Recirculation Valve position (feedback)
20c - Vehicle speed in kph, updating only once per second. (real speed, not speed+safety margin as in the speedometer)
21c - Engine RPM in hundreds. This too only updates once per second.
22c - ?
23c - ?
24c - Sun sensor, exterior lights switch & panel lights control (term. 58 & 58d voltage) - used for A/C panel display illum.
25c - ?
26c - ?
27c - ?
28c - Fan speed?
29c - ?
30c - Engine run time in seconds (255 max.)(=0xff)
31c - Timing counter
32c - Displays test
33c - Software version? Mine states 3.4
34c - ?
35c - Outside temp. from inlet sensor (filtered?)
36c - temp?

pat056

That's it Tim...thanks!
BTW, have you ever tried the oil temp function? I got a reading, but don't think it was oil temp.
I'm OC I guess. I always leave it on water temp.

Kevin H. in Atl..

One thing to remember when observing the oil temp is that there is an oil/water heat exchanger; the oil and water temps will fluctuate as the exchanger does it's thing.

Happy New Year!

BruceP

Here ya go:

Press and hold in the recirculate and the top (arrow up) buttons on the right side of the panel for a few seconds. The left screen will change. Using the + key below that screen, adance so the display reads 6c. Then press the center vent button once. Your coolant temp will be displayed.

Press AUTO to go back to normal.