Rennlist - Porsche Discussion Forums

Notices
 
Page 1 of 19
1
2
3
4
5
6
11
Last »
Search: Posts Made By: CBR786
Showing results 1 to 25 of 456
Search took 0.67 seconds.
Forum: 993 Forum
08-13-2019, 08:48 AM
Replies: 15
Views: 7,185
Posted By CBR786

have you fixed this issue? where are you located...

have you fixed this issue? where are you located in the UK? You need to look at all the pin connections going in the door jams on both doors maybe one pin has been slotted in to the wrong connector ?...
Forum: 996 Forum
02-15-2019, 12:57 PM
Replies: 6
Views: 1,221
Posted By CBR786

the shop I used where a bunch of idiots. They...

the shop I used where a bunch of idiots. They told me the system powers up via CANBUS but when I checked the wiring loom in the car I could not see a CANBUS (two wires intertwined) on the loom. I...
Forum: 996 Forum
02-14-2019, 01:49 PM
Replies: 6
Views: 1,221
Posted By CBR786

Thank you for the input Dan, I gave the head unit...

Thank you for the input Dan, I gave the head unit to a electronics shop to see if they can spot anything obvious they opened the unit and said it all looks good and no issues. They could not power it...
Forum: 996 Forum
02-12-2019, 12:10 PM
Replies: 6
Views: 1,221
Posted By CBR786

PCM2 SWAP OUT

hi I need some advice my PCM 2 has died well the screen and the CD disc is not ejecting from the PCM. When I pull it out and look at the rear of the unit the red optical signal is emitting from the...
Forum: 993 Forum
12-03-2018, 02:41 PM
Replies: 26
Views: 3,121
Posted By CBR786

Fixed it I ordered another thermistor but as I...

Fixed it I ordered another thermistor but as I was putting everything back to how it was I decided to pull the temperature sensor to get it ready for soldering in new thermistor. Once opened I heated...
Forum: 993 Forum
12-02-2018, 06:03 PM
Replies: 26
Views: 3,121
Posted By CBR786

forgot to mention the mixing chamber temps where...

forgot to mention the mixing chamber temps where car engine off not been running for the last 3 weeks or so but car in heated garage.
Forum: 993 Forum
12-02-2018, 06:02 PM
Replies: 26
Views: 3,121
Posted By CBR786

feeling like a fool lol I think I fixed my...

feeling like a fool lol
I think I fixed my problem giving updates so any one else in similar predicament does not go round in circles or waste money ! Luckily I am doing stuff in house this is why...
Forum: 993 Forum
11-18-2018, 07:54 PM
Replies: 69
Views: 11,393
Posted By CBR786

+1 I have had DME relays before that do not sit...

+1
I have had DME relays before that do not sit right in the fuse box and can cause you starting issue. I would get a friend or help to crank it while you lean the DME to one side so it is making...
Forum: 993 Forum
11-17-2018, 03:05 PM
Replies: 26
Views: 3,121
Posted By CBR786

JIB I know where you are coming from and no...

JIB I know where you are coming from and no offence taken lol. I just do not wish to buy a servo unit when it is something else that is faulty. I ruled out the servo units being faulty by doing a...
Forum: 993 Forum
11-17-2018, 01:48 PM
Replies: 26
Views: 3,121
Posted By CBR786

OK I had a chance to do some more tinkering today...

OK I had a chance to do some more tinkering today and these are my findings as follows. Wiring all back to how it should be in the bunch plugs etc. I pulled the CCU and pushed a tester wire into...
Forum: 993 Forum
11-14-2018, 12:05 PM
Replies: 26
Views: 3,121
Posted By CBR786

actually now that I am sitting in front of lap...

actually now that I am sitting in front of lap top and looking at Tore's copy of wiring diagram I should revert the left side wiring back to how it was originally meaning Pin 1 should be Green/White...
Forum: 993 Forum
11-14-2018, 11:40 AM
Replies: 26
Views: 3,121
Posted By CBR786

okay still no where near fixing this issue. I...

okay still no where near fixing this issue. I went into the garage with my strained shoulder as it was bugging me and I needed to have a little fettle with the car. As agreed I swapped the Servo's...
Forum: 993 Forum
11-13-2018, 05:27 PM
Replies: 26
Views: 3,121
Posted By CBR786

https://cimg1.ibsrv.net/gimg/rennlist.com-vbulleti...

https://cimg1.ibsrv.net/gimg/rennlist.com-vbulletin/2000x1504/f2b94080_3b34_44ec_a65f_119126e164c3_051f50f4f68b8ffdbe789580ca0f11d8565498c7.jpeg
965 ccu
965 CCU pin 1 is green/white for both...
Forum: 993 Forum
11-13-2018, 05:13 PM
Replies: 26
Views: 3,121
Posted By CBR786

Thank you to everyone who contributed towards...

Thank you to everyone who contributed towards helping me solve this issue. I have sprained my left shoulder or am suffering from a trapped nerve very painful causing limited movement of my left arm...
Forum: 993 Forum
11-11-2018, 04:03 PM
Replies: 26
Views: 3,121
Posted By CBR786

Thank you for the input Tore much appreciated it...

Thank you for the input Tore much appreciated it helps to know that the CCU automatically locks out certain outputs if the CCU does not see the correct position change from the servo. I think I made...
Forum: 993 Forum
11-10-2018, 06:01 PM
Replies: 26
Views: 3,121
Posted By CBR786

ok I am not sure but reading Tore's extensive...

ok I am not sure but reading Tore's extensive write up on his website about CCU I think I might need to buy TCA 2465 servo driver chip and solder this into the PCB. I just need to find out do I need...
Forum: 993 Forum
11-10-2018, 02:58 PM
Replies: 26
Views: 3,121
Posted By CBR786

I forgot to mention but not sure how relevant it...

I forgot to mention but not sure how relevant it is. The functionality of the CCU WORKS on every other function when testing with PST2 tester. The only issue is the A/C on the car has been removed no...
Forum: 993 Forum
11-10-2018, 02:49 PM
Replies: 26
Views: 3,121
Posted By CBR786

I guess I will need to pull the CCU and see what...

I guess I will need to pull the CCU and see what is going on with the output pins. I earlier today sourced a 964 servo and bench tested that by applying 12 v to pins 4-5. It worked fine on he bench....
Forum: 993 Forum
11-09-2018, 02:28 PM
Replies: 26
Views: 3,121
Posted By CBR786

https://cimg0.ibsrv.net/gimg/rennlist.com-vbulleti...

https://cimg0.ibsrv.net/gimg/rennlist.com-vbulletin/2000x1504/6ea03c45_6dc9_40bd_807a_ff9e83588e9e_ae16fd3fa77fcbab288af7cb9be6ecab18b2772c.jpeg
yellow
pic
Forum: 993 Forum
11-09-2018, 02:00 PM
Replies: 26
Views: 3,121
Posted By CBR786

CCU LEFT MIX FLAP

hello folks I need some guidance on my left mix flap as it is not working. I luckily have a PST2 tester which can assist me in trying to fault find. The PST2 tester through the drive links checked...
Forum: 993 Forum
10-29-2018, 10:44 AM
Replies: 15
Views: 7,185
Posted By CBR786

pic ...

pic
https://cimg1.ibsrv.net/gimg/rennlist.com-vbulletin/2000x2000/img_0059_f43d549c3170dea5ef9f7e144aa66b94d073a9cf.jpg
Forum: 993 Forum
10-28-2018, 08:21 PM
Replies: 19
Views: 2,157
Posted By CBR786

ha its a dry dusty country the cars get caked in...

ha its a dry dusty country the cars get caked in dirt fairly quickly! not abandoned. I say well done to the lad that bought the car. I hope he drives it hard before mothballing it away. The dumped...
Forum: 993 Forum
10-27-2018, 06:26 PM
Replies: 15
Views: 7,185
Posted By CBR786

Solved my problem. Central locking works both...

Solved my problem. Central locking works both doors now and when I use key both doors unlock no matter which door I use the key. Incidentally still no micro switches fitted on any door handle. The...
Forum: 993 Forum
10-26-2018, 04:59 PM
Replies: 9
Views: 833
Posted By CBR786

even cleaning the belt you would be surprised how...

even cleaning the belt you would be surprised how much dirt can add up on a black belt over the years. pull it all out and wash it in a bucket with soap and let it dry. can make it roll more better
Forum: 993 Forum
10-26-2018, 04:53 PM
Replies: 8
Views: 1,840
Posted By CBR786

I had something similar and my drive shaft bolts...

I had something similar and my drive shaft bolts on the gear box end where slightly loose !
Showing results 1 to 25 of 456
 
Page 1 of 19
1
2
3
4
5
6
11
Last »


 
Forum Jump


All times are GMT -3. The time now is 02:15 PM.